Recovery mode - Revision history

Z013: English corrections

2019-02-13T10:00:04Z

English corrections

Z013 at 12:56, 11 May 2018

2018-05-11T12:56:37Z

Z013 at 12:55, 11 May 2018

2018-05-11T12:55:42Z

Z013 at 12:55, 11 May 2018

2018-05-11T12:55:26Z

Z013 at 11:30, 11 May 2018

2018-05-11T11:30:49Z

Z013: Created page with "It's the state the IPLOG unit goes into when the operating system isn't stable enough to boot or when an OS device encounters software or app-related trouble, it can usually b..."

2018-05-11T11:29:02Z

Created page with "It's the state the IPLOG unit goes into when the operating system isn't stable enough to boot or when an OS device encounters software or app-related trouble, it can usually b..."

New page

It's the state the IPLOG unit goes into when the operating system isn't stable enough to boot or when an OS device encounters software or app-related trouble, it can usually be resolved by just restarting. In some circumstances, though, the problems are more extensive and require putting the device into recovery mode and restoring it.

Recovery mode is, in fact, is the basic firmware version without all of the user's applications and configurations.

Recovery mode is read-only. Every user's change wrote during Recovery mode will be removed after a device reboot.

During the Recovery mode, the unit is available to connect to the IP address found on the label on the side of the cased device. DHCP protocol is not available.

== How to go to Recovery Mode ==
The IPLOG has, usually on the front panel under power LED, a reset button. When the reset button is pushed during powering-up, it starts recovery mode.

Recovery mode is signalled by blinking green ST (state) LED.

@@ Line 1: / Line 1: @@
-It's the state the IPLOG unit goes into when the operating system isn't stable enough to boot or when an OS device encounters software or app-related trouble, it can usually be resolved by just restarting. In some circumstances, though, the problems are more extensive and require putting the device into recovery mode and restoring it.
+This is the state that the IPLOG unit goes into when the operating system isn't stable enough to boot or when an OS device encounters software or app-related troubles, it can usually be resolved by simply restarting. In some circumstances, though, the problems are more extensive and require putting the device into recovery mode and restoring it.
-Recovery mode is, in fact, is the basic firmware version without all of the user's applications and configurations.
+Recovery mode is, in fact, the basic firmware version without all of the users applications and configurations.
-'''Recovery mode is read-only.''' Every user's change wrote during Recovery mode will be removed after a device reboot.
+'''Recovery mode is a read-only.''' Every users change written during Recovery mode will be removed after the devices reboot.
 During the Recovery mode, the unit is available to connect to the IP address found on the label on the side of the cased device. DHCP protocol is not available.
-== How to go to Recovery Mode ==
+== How to get to Recovery Mode ==
-Recovery mode is entered when one of the following condition occurs:
+Recovery mode is entered when one of the following conditions occurs:
 * The IPLOG has, usually on the front panel under power LED, a reset button. When the reset button is pushed during powering-up, it starts recovery mode.
-* Internal SD card is not inserted during powering-up sequence.
+* The internal SD card is not inserted during the powering-up sequence.
 * Invalid image in NAND.
 {{Note|NoteText=
-Recovery mode is signalled by blinking green ST (state) LED.
+Recovery mode is signalled by a blinking green ST (state) LED.
 }}

@@ Line 11: / Line 11: @@
 Recovery mode is entered when one of the following condition occurs:
 * The IPLOG has, usually on the front panel under power LED, a reset button. When the reset button is pushed during powering-up, it starts recovery mode.
-* Internal SD card is not inserted during power-up sequence.
+* Internal SD card is not inserted during powering-up sequence.
 * Invalid image in NAND.

@@ Line 9: / Line 9: @@
 == How to go to Recovery Mode ==
-Recovery mode is entered when one of the following condition occurs
+Recovery mode is entered when one of the following condition occurs:
 * The IPLOG has, usually on the front panel under power LED, a reset button. When the reset button is pushed during powering-up, it starts recovery mode.
 * Internal SD card is not inserted during power-up sequence.

← Older revision		Revision as of 12:55, 11 May 2018
Line 8:		Line 8:

	== How to go to Recovery Mode ==		== How to go to Recovery Mode ==
−	~~The IPLOG has, usually on the front panel under power LED, a reset button. When the reset button is pushed during powering-up, it starts recovery mode.~~

		+	Recovery mode is entered when one of the following condition occurs
		+	* The IPLOG has, usually on the front panel under power LED, a reset button. When the reset button is pushed during powering-up, it starts recovery mode.
		+	* Internal SD card is not inserted during power-up sequence.
		+	* Invalid image in NAND.
		+
		+	{{Note\|NoteText=
	Recovery mode is signalled by blinking green ST (state) LED.		Recovery mode is signalled by blinking green ST (state) LED.
		+	}}