Difference between revisions of "QuickStart"
(→TCP connection) |
|||
| Line 1: | Line 1: | ||
This document explains how to start using IPLOG-GAMA. | This document explains how to start using IPLOG-GAMA. | ||
| − | == TCP | + | == TCP Connection == |
=== DHCP (Dynamic Host Configuration Protocol) === | === DHCP (Dynamic Host Configuration Protocol) === | ||
| − | During the system booting or ethernet cable connections, IPLOG sends DHCP request to the server, | + | During the system booting or ethernet cable connections, IPLOG sends a DHCP request to the server, |
| − | if DHCP server dynamically assigned an IP address and other network configuration parameters then | + | if the DHCP server has dynamically assigned an IP address and other network configuration parameters then |
IPLOG is available on the TCP parameters of your network. | IPLOG is available on the TCP parameters of your network. | ||
=== Static IP address === | === Static IP address === | ||
| − | In the | + | In the event, DHCP is not available the unit interface is set to the TCP parameters of the case (IP address 10.x.x.x, mask 255.0.0.0). |
* DHCP and Static IP address services are available at the same time. | * DHCP and Static IP address services are available at the same time. | ||
| Line 33: | Line 33: | ||
| − | ''' | + | '''Recommendations''' |
# Connect an ethernet cable to the ethernet port on the unit | # Connect an ethernet cable to the ethernet port on the unit | ||
# Connect power (10-60VDC) | # Connect power (10-60VDC) | ||
# Wait 15 seconds (TBC) | # Wait 15 seconds (TBC) | ||
| − | # Set your computer to the same IP range as IPLOG | + | # Set your computer to the same IP range as IPLOG (assigned by DHCP server or please check the static address on the case of the IPLOG). For communication via static IP address, for example, set your computer interface to '''10.0.0.10/255.0.0.0''' |
== Communication == | == Communication == | ||
=== SSH === | === SSH === | ||
Secure Shell (SSH) is a cryptographic network protocol for operating network services securely over an unsecured network | Secure Shell (SSH) is a cryptographic network protocol for operating network services securely over an unsecured network | ||
| − | * Download | + | * Download programs supported by SSH, for example, PuTTY |
* Run PuTTY and enter username "root" (password is not needed) | * Run PuTTY and enter username "root" (password is not needed) | ||
| Line 53: | Line 53: | ||
== METEL IEC 61131-3 IDE (Programming) == | == METEL IEC 61131-3 IDE (Programming) == | ||
| − | Is an | + | Is an Advanced Tool for Automation/Control Tasks: |
* programming of automatic action (EM) | * programming of automatic action (EM) | ||
* advanced control and automation tasks | * advanced control and automation tasks | ||
* debug configured automation / EM tasks | * debug configured automation / EM tasks | ||
Revision as of 05:34, 4 May 2018
This document explains how to start using IPLOG-GAMA.
Contents
TCP Connection
DHCP (Dynamic Host Configuration Protocol)
During the system booting or ethernet cable connections, IPLOG sends a DHCP request to the server, if the DHCP server has dynamically assigned an IP address and other network configuration parameters then IPLOG is available on the TCP parameters of your network.
Static IP address
In the event, DHCP is not available the unit interface is set to the TCP parameters of the case (IP address 10.x.x.x, mask 255.0.0.0).
- DHCP and Static IP address services are available at the same time.
root@buildroot:~# cat /etc/network/interfaces
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp
pre-up /etc/network/nfs_check
wait-delay 15
auto eth0:0
iface eth0:0 inet static
address 10.68.0.6
broadcast 10.255.255.255
netmask 255.0.0.0
Recommendations
- Connect an ethernet cable to the ethernet port on the unit
- Connect power (10-60VDC)
- Wait 15 seconds (TBC)
- Set your computer to the same IP range as IPLOG (assigned by DHCP server or please check the static address on the case of the IPLOG). For communication via static IP address, for example, set your computer interface to 10.0.0.10/255.0.0.0
Communication
SSH
Secure Shell (SSH) is a cryptographic network protocol for operating network services securely over an unsecured network
- Download programs supported by SSH, for example, PuTTY
- Run PuTTY and enter username "root" (password is not needed)
BASH
- configure LAN interfaces (IP, DNS...) and other IOs (for example ranges at alarm loops, output ranges at analogue outputs 0-10V )
- monitoring of LAN interfaces and other IOs
- writing of scripts
- download and install Linux packages (thanks to Linux, we have the first working application sending emails via Gmail)
METEL IEC 61131-3 IDE (Programming)
Is an Advanced Tool for Automation/Control Tasks:
- programming of automatic action (EM)
- advanced control and automation tasks
- debug configured automation / EM tasks
